Cisco PWR-C1-715WAC/2 Full Official Product Description
1. Part Number & Naming Definition
Official Full Name
Cisco 715-Watt Hot-Swappable Standard Efficiency AC Power Supply Module (Config 1, Secondary Commercial Variant)
SKU:PWR-C1-715WAC/2
Naming Breakdown
-
PWR: Modular power supply unit
-
C1: Config 1 unified form factor for Catalyst 3850 / Catalyst 9300 switch chassis
-
715W: Maximum rated DC output power of 715 Watts
-
AC: Universal alternating current mains input
-
/2: Secondary spare commercial variant, mechanically, electrically and firmware compatible with base PWR-C1-715WAC
Critical Note: Identical electrical parameters, pin assignment and physical dimensions as standard PWR-C1-715WAC. Fully interchangeable within all supported chassis without hardware modification. Distinguish from high-efficiency PWR-C1-715WAC-P Platinum model.
Core Architecture
The PWR-C1-715WAC/2 is a hot‑swappable AC‑DC switching power module equipped with integrated temperature‑controlled variable speed cooling fan. It converts universal AC mains input to regulated -56 VDC output to power switch mainboard, internal fan assemblies and medium-to-heavy PoE loads. It supports parallel 1+1 redundant deployment and automatic load sharing inside compatible switch chassis. Embedded protection circuits deliver overvoltage (OVP), overcurrent (OCP), overtemperature (OTP) and short‑circuit auto‑recovery protection.
Deployment Guidance: This 715W power module provides sufficient power budget for switches running IEEE 802.3af (PoE) and IEEE 802.3at (PoE+) endpoints such as IP phones, wireless access points and IP surveillance cameras.
Core Product Positioning
The Cisco PWR-C1-715WAC/2 is a field-replaceable hot‑swappable AC power supply designed for Catalyst enterprise access switches with medium to heavy PoE power demands. Suitable as primary or redundant power source for PoE-enabled switch deployments. Dual PSU installation eliminates single point of failure and enables live power module replacement without switch shutdown. Widely deployed in enterprise campus access networks, medium-density PoE LAN environments and branch office switching infrastructures built on Catalyst 3850 and Catalyst 9300 fixed-form-factor switches.
2. Hardware & Software Compatibility
Supported Host Platforms
-
Cisco Catalyst 3850 Series fixed-port switches (all PoE and non-PoE variants)
-
Cisco Catalyst 9300 modular switches (all PoE+ and non-PoE models)
-
Cisco Catalyst 9300X modular switches
Unsupported Platforms
C9200 / C9200L, C9300L, Catalyst 3650, Catalyst 9400/9500, ISR routers, ASA firewalls and all non‑C1‑config chassis.
3. Electrical & Physical Specifications
Electrical Ratings
-
Input Voltage: 100–240 VAC autoranging, 50/60 Hz
-
Input Current: 10 A @100 VAC / 5 A @240 VAC
-
Input Connector: IEC 60320 C16
-
DC Output: -56 VDC, maximum 12.8 A (715 W)
-
Minimum Hold-up Time: ≥16.7 ms @100 VAC input
-
Cooling: Integrated temperature-controlled variable speed fan
-
Efficiency: Standard efficiency AC power module
-
Protection: OVP, OCP, OTP, short-circuit automatic recovery
Physical Specifications
-
Dimensions (H × W × D): 40.1 × 82.6 × 309.9 mm (1.58 × 3.25 × 12.20 inch)
-
Approximate Unit Weight: 1.2 kg
Environmental Specifications
-
Operating Temperature: -5 °C ~ +45 °C
-
Storage Temperature: -40 °C ~ +70 °C
-
Operating Humidity: 5% – 95% non‑condensing
-
Maximum Operating Altitude: 3048 m (10,000 ft)
4. Supported Functional Capabilities
Power System Functions
-
Online Insertion and Removal (OIR) hot-swap capability
-
Parallel 1+1 redundant power mode and dynamic load sharing
-
Real-time PSU health monitoring via IOS-XE CLI, SNMP and Cisco DNA Center
-
Dynamic fan speed adjustment based on internal ambient temperature
-
Fault alert reporting for overheating, power loss and hardware faults
Platform Feature Compatibility
Supports StackPower power pooling function when installed within stacked Catalyst 3850 / C9300 switch systems. Fully compatible with all native Layer 2 / Layer 3 switching functions of supported host platforms.
5. Typical Deployment Scenarios
-
Primary or redundant power supply for PoE/PoE+ Catalyst 3850 / C9300 access switches
-
Enterprise access networks deploying multiple PoE wireless APs, IP phones and IP cameras
-
Medium-scale campus and branch office switching requiring flexible PoE power budgeting
-
Network environments requiring zero-downtime hot replacement of power modules
-
Cost-sensitive PoE deployments without strict platinum high-efficiency requirements
6. Regulatory & Compliance Certifications
-
Safety: UL 60950-1, IEC 60950-1
-
EMC: CE, FCC Part 15 Class A, ICES-003 Class A
-
Environmental: RoHS compliant
7. Standard Factory Package Contents
1 × Cisco PWR-C1-715WAC/2 power supply module
Hardware installation documentation
AC power cord sold separately; select regional C16 power cables as required.
Model Comparison Reference
-
PWR-C1-715WAC/2: 715W standard efficiency AC PSU, Config 1, secondary commercial variant
-
PWR-C1-715WAC: Base standard 715W AC power supply, electrically identical
-
PWR-C1-715WAC-P: 715W 80 PLUS Platinum high-efficiency AC variant
-
PWR-C1-350WAC / PWR-C1-350WAC-P: 350W lower-capacity Config 1 power supplies
-
PWR-C1-1100WAC-P: 1100W Platinum AC PSU for high-density UPOE deployments
-
PWR-C1-715WDC: 715 Watt -48VDC DC-input power supply
UNSPSC Classification Code
43211702 – Network equipment internal power supply module
Hardware Warranty
Genuine Cisco original hardware carries Cisco standard one-year hardware warranty. Refurbished units follow respective supplier warranty terms.
|
