Cisco ISR8200-FAN Full English Description

Product Overview

Important Hardware Note: Two airflow options are available:

• PI = Port-Side Intake (cold aisle airflow, air enters port side)
• PE = Port-Side Exhaust (hot aisle airflow, air exhausts from port side)
  All fan modules and power supplies installed in the same routermust share identical airflow direction. Standard ESD anti-static handling procedures are mandatory during maintenance. These fan modules cannot be interchanged with ISR4000 series, ASR series or Catalyst switch fan trays.

Key Features

1. Intelligent Variable-Speed Thermal Regulation

   Each fan module dynamically adjusts rotor rotational speed according to real-time internal chassis temperature and ambient altitude. Fans run at low RPM under light traffic loads to minimize power consumption and acoustic noise, and automatically ramp up speed to boost airflow when temperatures rise. All thermal telemetry is monitored and reported via Cisco IOS XE.
2. Dual Selectable Airflow Architecture

• PI (Port-Side Intake): Air intake at rear port side, exhaust toward front bezel
• PE (Port-Side Exhaust: Air intake at front bezel, exhaust toward rear port side
  Match airflow type to data center cold/hot aisle layout. Maintain unobstructed ventilation space around the chassis to avoid airflow blockage and thermal hotspots.

1. OIR (Online Insertion and Removal) Support

   The fan module fully supports hot-swap replacement while the router remains powered and forwards live traffic. If one module is removed, remaining active fan modules automatically increase speed to compensate cooling capacity. Do not leave empty fan slots for extended periods; maximum safe operation time with missing fan module is limited to avoid over-temperature shutdown. IOS XE automatically recognizes and validates fan hardware after installation.
2. System Monitoring & Alarm Notification

   IOS XE continuously monitors individual fan rotor RPM status.

• Solid Green LED: All internal fan rotors operate normally
• Amber LED: Fan rotor fault detected within the module
  The system generates console syslog messages and SNMP traps to notify network administrators once fan anomalies occur.

1. N+1 Fan Redundancy

   Chassis adopts distributed modular fan architecture. Single fan module failure does not cause immediate outage; remaining modules provide temporary adequate cooling. Engineers should schedule immediate FRU replacement upon receiving fault alerts to eliminate long-term cooling risk.
2. Enterprise & Carrier-Grade Reliability

   High-performance industrial brushless DC fans designed for 24/7 continuous operation in medium-to-large enterprise branch SD-WAN edges, multi-service internet gateways and carrier Ethernet aggregation deployments. Optional external dust filter accessories are available for harsh operating environments.

Supported Hardware Platforms

• Cisco 8201 Secure Router (1RU)
• Cisco 8201-24H8FH / 8201-32FH Secure Router (1RU)
• Cisco 8202 Secure Router (2RU)
• Cisco 8202-32FH-M Secure Router (2RU)

Not compatible: ISR4300/ISR4400 series, legacy ISR 3900/3800, ASR aggregation routers, Nexus / Catalyst switching platforms.

Typical Application Scenarios

• Enterprise medium branch SD-WAN, internet edge and unified security gateway deployments running IOS XE on Cisco 8200 series routers
• Spare replacement cooling fan modules for data center and branch router maintenance
• Network infrastructure upgrade supporting flexible cold/hot-aisle airflow requirements

Technical Specifications

• Form Factor: Front-access hot-swappable independent fan module
• Official PIDs:
  1RU models: FAN-1RU-PI, FAN-1RU-PE, FAN-1RU-PI-V2, FAN-1RU-PE-V2
  2RU models: FAN-2RU-PI, FAN-2RU-PE
• Airflow Options: Port-Side Intake (PI) / Port-Side Exhaust (PE)
• Hot Swappable (OIR): Fully supported
• Monitoring: Per-fan RPM monitoring, module status LED, IOS XE syslog & SNMP trap support
• Operating Ambient Temperature: 0°C ~ +40°C
• Compliance: UL, CE, RoHS, NEBS compatible

Short Version for E-commerce Listing